World wide free shipping on orders over 120€ – PayPal and Stripe payments – Made in Finland
What temperature should you keep in a garage?
The suggested temperature in a garage is no less than 5° C, preferably between 12° C and 15° C. The temperature does not necessarily need to be over zero degrees Celsius if the relative humidity remains low enough. Additionally, if there are water pipes vulnerable to freezing, it is important to avoid subzero temperatures.
A garage is often a semi-heated space where humidity may cause unwanted issues. If you do not want to maintain high temperatures in the garage, then efficient ventilation is required to prevent moisture build-up. Excessive moisture can expose structures to mould and stored property to rust.
A wet car or a baby stroller in the garage can raise the relative humidity to as high as 95%. Keeping garage doors open on the other hand may also affect the humidity, especially if it is very humid outside. Optimal humidity in the garage should be around 45% to 50%.
RuuviTags perform as excellent guards against excessive humidity and subzero temperatures. We recommend the RuuviTag Pro (3in1) for your garage. It measures temperature, humidity and motion. It is recommended to occasionally check that the Bluetooth range is good enough to avoid any unpleasant surprises. If necessary, you can get a longer range by linking your tag or multiple tags with a Ruuvi Gateway router. The Ruuvi Gateway and Cloud service also provide customisable and secure email alerts.
RuuviTag in a garage
Buy Combined Thermometer And Hygrometer to Garage
Measure temperature and humidity in your garage and save on heating costs
In stock
Buy Combined Thermometer And Hygrometer to Garage
Measure temperature and humidity in your garage and save on heating costs
Works as expected. I’m using three of these with a Victron system. Unfortunately Victron doesn’t seem to support the Motion feature, and the only way to see Pressure is deep in the menu’s or via VRM. Those are likely more the fault of Victron than Ruuvi, so I can’t complain too much. I primarily wanted Temps and Humidity on the Victron Remote Console, which I have now thanks to this product. I should point out, this only works with the “New” GUI. If you’re using the old v1, none of the sensor info will display on that one.
I am using your sensor for experiments—specifically, to build a system that allows me to monitor and evaluate room temperatures via a smartphone. Each room is equipped with a sensor and an ESP32-S3 microcontroller (photo) that scans it using BLE. The microcontroller then transmits the data to the cloud via an MQTT bridge. This data can be displayed on a phone connected to the corresponding MQTT topic (video).
Regarding the sensors, I can say the following: 1) They work 😊 2) The sensors have significant inertia: if you move a sensor from one room to another, it doesn’t adjust to the actual temperature instantly but takes a few minutes to do so. 3) If two sensors are placed in the same room, their readings—specifically temperature and humidity—can differ significantly; for instance, the temperature might vary by half a degree to a full degree. 4) The cost of the sensors—and especially shipping them from Finland—is quite high. So far, I have purchased only two. 5) I hope I’ve satisfies your curiosity.
NB! Unfortunately, I am unable to attach images and videos: I get an error stating that the 25 MB limit has been exceeded, even though both the photos and videos are well below that limit.
Super easy installation in Victron Cerbo GX. Pull the tab for the battery, name your device and add some other information and you’re done. The configuration is faster than opening the box. And they work 100 % for me. I use six: one per engine room in my catamaran, one in the fridge, one in the freezer, one outdoors and one in the owner’s cabin. If I ever need more I know where to go. And by the way, all temps available online even when I am far from the boat.
Highly precise sensor that is very easy to pair, especially when used with Victron control units.
Einfache Installation. Macht was er soll
I am using your sensor for experiments—specifically, to build a system that allows me to monitor and evaluate room temperatures via a smartphone.
Each room is equipped with a sensor and an ESP32-S3 microcontroller (photo) that scans it using BLE. The microcontroller then transmits the data to the cloud via an MQTT bridge. This data can be displayed on a phone connected to the corresponding MQTT topic (video).
Regarding the sensors, I can say the following:
1) They work 😊
2) The sensors have significant inertia: if you move a sensor from one room to another, it doesn’t adjust to the actual temperature instantly but takes a few minutes to do so.
3) If two sensors are placed in the same room, their readings—specifically temperature and humidity—can differ significantly; for instance, the temperature might vary by half a degree to a full degree.
4) The cost of the sensors—and especially shipping them from Finland—is quite high. So far, I have purchased only two.
5) I hope I’ve satisfies your curiosity.
NB!
Unfortunately, I am unable to attach images and videos: I get an error stating that the 25 MB limit has been exceeded, even though both the photos and videos are well below that limit.
Super easy installation in Victron Cerbo GX. Pull the tab for the battery, name your device and add some other information and you’re done.
The configuration is faster than opening the box. And they work 100 % for me. I use six: one per engine room in my catamaran, one in the fridge, one in the freezer, one outdoors and one in the owner’s cabin. If I ever need more I know where to go. And by the way, all temps available online even when I am far from the boat.
Best sensor you can get! Not the last I bought!
Works well.